Category Archives: Jim

On to Lexington

Teardrop Trail Log: June 14, 2016

photo of stuffed bear in Pat's Army Store

Pat’s Army Store Inmate

I was introduced to historic Lexington, Missouri when I was in the neighborhood for a presentation in June on my cookbook – Canning, Pickling and Freezing, with Irma Harding. The meeting of the Missouri Cattlewomen was held at the historic Elms Resort and Spa in Excelsior Springs. I researched the Resort built in 1898, and discovered it was “haunted.” I had previous experience with haunted hotels when I worked in Santa Fe so I felt right at home. Actually, the hotel had several interesting guests including Al Capone and Harry S. Truman. It was an amazing experience. My talk, “Eat, Drink, and Pickle!” was at VanTill’s Family Farm & Vineyard. I fell in love with the area and the people.

River Reader

As we left Kansas City, I was looking at the atlas and Lexington was only about 50 miles away. We were so close, I suggested we take a side trip so Jim could meet my friends and see Lexington where there is lot’s of history from the Civil War. After parking the Lady and the Ambassador, we stopped in at Pat’s Army Store, located in an old Baptist Church. Next, we stopped by the Old Trails Region to see Marsha Corbin, my host. I met Marsha at last year’s Red Power Round Up where she’d heard my presentation. She was just down the street for a meeting, so we proceeded to say hello. Next stop was one of the most amazing independent bookstores, River Reader owned by Pat and Gary Worth. I had a great book signing at River Reader. Pat offered a couple of bottles of cold water on the warm day and It was nice to connect everyone with Jim.

We left River Reader and Jim was taken by the scenic beauty of the town. The Greek Revival Lafayette County Courthouse built in 1847 and other historic buildings led the town to bill itself as the “Athens on the Missouri” and became subjects for his photography.

: The old Baptist Church

: Second Baptist Church

: Lafayette County Courthouse

: One of many antique stores

: Lexington Façades 1

: Lexington Façades 2

: Lexington façades 3

: Lexington Façades 4

A Masked Marauder – Raccoon!

Teardrop Trail Log: June 13, 2016

Travel completed, we arrived at Lake Jacomo County Park near Kansas City and our cares dissipated. The place looks more like a city park than a camp ground with a well-manicured lawn and plantings, and a stylish restroom and bathhouse. Best of all, Marilyn had thoughtfully stashed a beer or two into the ice chest. I would have cold beer even though the solar fridge system had failed. We each began our setup and dinner tasks.

The weather was warm but not too bad, and I enjoyed setting up camp. Marilyn was already working on dinner — a chicken recipe that we both like. With the new stabilizers, I was done in no time, and sat down to enjoy a cold one while checking the day’s events. The prospect of a a leisurely dinner in the twilight beckoned.

As we sat down to dinner about 30 minutes later, we heard a crash by the camp picnic table. Investigating, Marilyn discovered the pasta pot had been knocked to the ground. This was new. There was no wind to speak of, and we weren’t near any other campsites. What was going on?

North American Raccoon (theivous cuteus)

I then noticed some movement near the tree. iPhone at the ready, I snapped a picture, the flash went off, and we had the evidence. There was a raccoon relaxing by the tree and apparently pondering it’s next move. Attracted by the pasta cooking water, it was unconcerned and seemed to say: “I’ll just wait here for dinner.” As we finished our dinner rituals, I spotted it outside of camp again — eyes aglow from my flashlight. Hmmm. Very persistent and comfortable around humans. Did we have a new challenge for our trip?

Patience and persistence personified

There Be Dragons …

Teardrop Trail Log: June 13, 2016

I guess I should be grateful we didn’t have more problems. If you think about it, trailering is an unlikely pastime, wherein one drags a small metal box on wheels at high speed over sometimes nasty, bumpy roads and expects everything to arrive at the same time. Then there’s the summer heat, rain, and wind — all of which can be extreme. Top it off by camping in the woods with open campfires, animal encounters and rutted trails masquerading as roads, and it’s a wonder things go as smoothly as they do. It’s a testament to the essential hopefulness and naïveté of the average camper. Certainly it describes our view of staying in the woods.

Repairing the antenna tube

Looking back, I understand our first several trips were usually trouble-free. Perhaps it was payback time. After a day of construction, rain, and detours, I thought we might have taken our lumps. As it turned out, we were just getting started. Day 2 dawned cool and overcast, and wonder of wonders, there was a Starbucks nearby. We went in and ordered, and within minutes I was in possession of the magic elixir. A Mocha. On the way back to the rig, I noticed that the antenna storage tube was askew. One of the supports had broken. Better fix it.

I decided to run our solar beer cooler while we were on the road. The day promised to be sunny, and I would have cold beer while setting up camp. Off we went through Paris, Texas, on our way to Joplin. Easy travel.

Dropping voltage

Since I was curious how much power we were generating and using with the beer cooler, I checked the voltage monitor every time we stopped. The battery voltage was falling slowly, suggesting the solar panel wasn’t keeping up, but nothing to worry about. Then during one of our stops, I noticed that the battery voltage had dropped by two volts. Not normal behavior. Considering the problem while we drove the next leg of the trip, I realized that one cell in the battery had catastrophically failed. This battery was toast.

We would have to find another. Marilyn got to work with the maps. As she plotted routes and queried the web, I mused on the rotten luck. What were the odds? Batteries don’t normally fail like this. On the other hand, it was over a year old. Maybe the battery maintainer wasn’t very good. Then, she announced her result. There was a Costco in southeast Kansas City, and going there would only take us a few miles out of our way. The camping gods had smiled.

We stopped at Costco, bought a replacement battery, and installed it in the parking lot to recover the core charge. Even so, we arrived at the Jacomo Campground by 7. Plenty of light to set up while Marilyn cooked a delicious dinner. Maybe we had finally paid our karma debt and could sail unconcerned into the adventure!

A New Battery

Kansas City Bound

Teardrop Trail Log: June 13, 2016

The clerk touted the free Wi-Fi during check-in at Camp Motel 6. As we sorted through our soggy gear, anxious to catch up on email and other online delights after a challenging day on the road, we soon realized that the results were grim at best. Jim, who had lots of experience in many things tech, described it as a data dribble. Later I would read that we had encountered the perfect storm of hotel Wi-Fi problems – lack of workable access and very poor capacity. The “perfect” end to the “perfect” day – #WiFiFail. The outside world would have to wait. It was time to turn off the lights and drift off to sleep, listening to the sounds of the rain outside.

Classic IHOP breakfast

In the morning, we headed to IHOP, located conveniently across the parking lot. Normally, we would seek out the most amazing local eatery for a culinary adventure, but today we needed to go promptly. As we entered, a flood of memories returned – many road trips as a child with stops at IHOP. The chain started in 1958 and continues to offer predictability in each of its 1,650 restaurants around the world. Chow time! Bacon, eggs, hash browns and toast. Comfort food on the road.

We loaded the Ambassador and headed north. Paris, Texas, up through Oklahoma and on to Missouri. We had been in Missouri last summer for Red Power Round Up in Sedalia. Rather than exploring off the beaten path, this time we elected to hit Interstate 49 for Kansas City. We would be meeting Sarah Tucker, the editor of Cool Tears magazine. She had suggested a county campground near her home. Yes, we were on the Teardrop Trail again….

The Adventure Begins …

Teardrop Trail Log: June 12, 2016. Red Power Roundup trip start.

Building, modifying, cleaning, planning and packing complete, the day of departure finally arrived. If we didn’t have it, we didn’t need it. We left midday, intending to reach Lake Bob Sandlin State Park in northeast Texas by early evening. Marilyn had a route, and it looked like a great day for travel.

All went well for the first hour or two and we joined I-35 at Round Rock. It was Sunday and I commented on how well traffic was moving. I must have jinxed it, because we encountered the first construction shortly after around Salado, and it continued all the way to Waco. What should have been an hour took more that two. Not a great start.

American Lotus (Nelumbo lutea)

To avoid further construction, we turned onto Highway 31 towards Corsicana, reasoning we would see the back country, and go through a few quaint, small towns. The scenery was beautiful, and we encountered a vast expanse of American Water Lilies in Henderson County between Trinidad and Malakoff. We pulled into the roadside park to make photos. The sky was threatening however, with consequences later in the day.

The sky threatened …

Turning north on Highway 19 at Athens, Texas, we were still making good time. Marilyn wanted to head northeast, more directly toward the state park. At Canton, we turned onto FM 17 (a two-lane “farm to market” road). More great scenery. Lush fields of hay with stands of tall pine trees dotted the landscape, set off by a dramatic sky. Although not Interstate speeds, we were sailing along when …

A fiery road-block near Fruitvale, Texas

We encountered a blazing car fire with traffic stopped in both directions. Sitting in the long line of cars for about 10 minutes, it was clear that it might be hours before the road opened. We had to go back. Now I had to turn our rig around on a narrow, two-lane road with no shoulders and no place to pull out — all with an audience of the several dozen.

Perfect.

Marshaling my best backing skills, I completed the U-turn in a few minutes. Thank goodness our rig is small. Anything larger and we would have been stuck. Retracing our steps back to Canton, we took I-20 West and re-joined Highway 19.

By now the light was fading, and we would have to set up in the dark. We’ve done it before, and it’s not so bad. Then it started to rain. Hard. Driving toward Sulphur Springs, the downpour worsened, with poor visibility as well. Perhaps a nice motel room would be best.

Reaching Sulphur Springs and I-30, we headed east toward Mount Pleasant. Marilyn called ahead and made a reservation. Arriving around 10, we loaded into the room in the pouring rain. Although low cost, a warm, dry room seems like a palace when compared with setting up in a dark, rainy campsite. Roughing it in a Motel 6 is still camping, right?

Mt. Pleasant Motel

Easy Leveling with an Atwood Stabilizer Jack

Jim, July 31:

The new storage box and galley table would certainly improve our setup and strike time, but I was sure it could be improved a little more. When we drive into a campsite, one of the first jobs is to level the trailer. Up to now, I used two scissor jacks (one under each rear corner of the trailer) and that worked well enough. Scissor jacks are fiddly and can be hard to use. They certainly aren’t quick. The light-weight jacks had to be extended by hand until they could be wedged under the trailer because they would “dance around” while turning the adjustment screw. They couldn’t be stored under the trailer. I thought we could do better.

Atwood Stabilizer Jack — Deployed

Looking around at other RVs, I learned about a “stabilizer jack”. Intended for leveling a trailer and designed to store under it, they seemed to fit the bill. A quick cruise on Amazon, and we had a candidate — the Atwood 82301stabilizer jack. I ordered a set of three. One for the tongue and one for each rear corner.

The Atwood stabilizer jacks can be either bolted or welded onto the trailer. My friend Jason at Vintage Motor Car agreed that welding would be best. A day or two later, they were installed. A little black spray paint, and the job was done.

Atwood Stabilizer Jack — Retracted

The jacks hide under the trailer when not in use, and only take a couple inches of ground clearance. Deployment is easy. Pull into the site, swing the two rear jacks down into the locked position and then deploy the front stabilizer jack the same way. The trailer sits pretty low to the ground, so occasionally I dig a little ground out from under the jack before it swings into place.

Jack handle in use

The final step is using the steel handle to adjust each jack’s height while watching a bubble level. The recommended jack handle (purchased separately) is rather short and will only install in the jack if all the holes are perfectly aligned — not always the case. A “heel” pry bar with a tapered end is both longer and will work with less perfectly aligned holes. The 16-inch pry bar (purchased in a set of four for $12 from a Red Power Roundup tool vendor) was the perfect size. Amazon has a similar product from about $25.

Pry Bar Set

Each stabilizer jack has a 650-pound work capacity and a 1000-pound support capacity. They measure 11 1/2-inches retracted and extend to 17 3/4-inches. I carry an assortment of wood blocks from 1/2-inch to 3 1/2-inches in thickness to account for sloping campsites. Also, I carry one scissors jack for unforeseen circumstances from pulling a stuck trailer hitch to changing a tire. That satisfies my “belt and suspenders (and belt)” approach. So far, we’ve been able to meet every camping challenge!

Pry Bar vs. Atwood jack handle

New Countertop for the Galley

Jim, July 24:

Trailer kitchen in the living room.

The Problem

Over the last several trips, I realized we were spending a lot of time setting up and striking each campsite. The lack of storage was corrected with the tongue box, but the Timber Creek Camp Kitchen took too long to set up. We needed another surface for the stove. I began to think about a counter that would hang on the galley edge.

There were several criteria. It had to attach with little modification and compliment the style of the teardrop. It had to store easily and be strong enough to support a two-burner stove with pans and skillets. And of course, it had to set up quickly. The raised lip at the back end of the galley could be used as an attachment point, but without legs supporting the other end because of the trip hazard. The best solution was to cantilever the counter with support from the underside of the trailer. Time’s a wastin’!

The Build

Initial mockup

I cut a 21-inch by 26-inch piece of birch plywood. This was the largest surface that would mount in the hatch opening without interfering with the galley storage. It was long enough to support our camp stove with a propane bottle. Next, I cut 9-inch pieces of 3/4-inch steel strap and bent one end to form an “L”. These fit into the gap between the galley countertop and hatch lid while attaching to the plywood. Using a couple of clamps, I mocked up the proof of concept. Success!

Trial fit of support pattern

Now for the cantilever supports. I wanted a design that would fit our teardrop. I drew a shape on a scrap of masonite and cut it with a saber saw. A trial fit with the table mockup looked promising, but I would have to match the curving shape of the trailer exactly. Several rounds of cut and fit were needed. Houston, we have a pattern.

I used the pattern to cut two pieces of plywood. Time for an edge treatment. I routed a 1/2 by 3/8-inch rebate in a piece of birch 1 by 2. This would cover the plywood laminations on the edge of the table, flush with the top. A table saw and a 45º sled made quick work of cutting the birch edges to length. A quick glue-up and I was done for the night.

: Initial assembly

: Detail of edge treatment

: All glued up

Let’s Finish This

The interior of our teardrop is varnished, and the wood and polished aluminum go well together. I sanded all the table parts and coated them with boiled linseed oil. We were running short of time before our trip, and the oil would protect the wood. I’ll add a more durable finish later.

: Folded table will travel in the galley

: Linseed oil finish

: Level and plumb

Linseed oil dried, I mounted the supports to the table with piano hinges. Another trial fit, and all was well. Folded, the table fits flat on top of the galley storage for transport. Finally, I drilled holes through the steel straps into the galley edge and threaded them for thumb screws. This prevents the table from detaching while in use. Level and plumb, the galley was ready!

Ready for camping!

Marine-Style 12 Volt Outlets in Our Teardrop

Jim, July 23:

One thing we learned on our trip to Big Bend, we needed more power outlets! With two smart phones, an iPad, a laptop, two cameras and other low-voltage doodads and geegaws, the two 12-volt and two 120-volt outlets that came with the trailer were simply not enough. Multi-outlet USB chargers helped, but added to the clutter in the cabin — especially at night. Also, the existing outlets were located on the aft interior and galley walls. Not convenient for charging while reading in bed.

Galley outlets

We had been working on a friend’s tiny house, and learned that the universe of 12-volt equipment has greatly expanded in the last couple of years. The tiny house was equipped with a marine power center, and offered 120/240-volt and 12-volt service. Just what was needed while at shore or underway. We equipped the tiny house entirely with 12-volt lighting, and easily found fixtures, light bulbs and other 12-volt outlets. With all the interest in solar power the number and quality of such devices is rapidly improving, and a trip to the Amazon store yielded several marine-style USB, cigar lighter and battery monitor fixtures.

USB power outlet detail

Fortunately, the Ambassador has hollow wood-paneled walls, so expanding the existing 12-volt wiring wasn’t too difficult. I simply replaced the two 12-volt cigar outlets with double and triple-gang devices on the back wall of the cabin and galley, while adding a pair of USB outlets on the forward wall under the cabin light. The marine system is nice because the 2 or 3 position panels can accept any combination of outlets and monitoring.

Now we can read in bed while charging our iPhones and other USB and cigar-lighter-based devices. Perfect!

: Interior — looking aft

: Interior — looking forward

: Cabin light and USB power outlet

A Trip to Krause Springs

Marilyn

Jim, July 22:

Marilyn was eager to connect with teardrop trailer enthusiasts and looked for groups we might join. The Southwest Teardrop & Vintage Trailers had a scheduled meetup in May and we decided to go. The three-day event was more than our time allowed, so we drove up for the day on Saturday. That way, we could make some new friends and check out Krause Springs at the same time.

Krause Springs

Located in the Texas Hill Country off Highway 71 on the way to Llano, the privately-owned, 115 acre park has been in operation since 1955. It’s on the National Registry of Historic Sites and has been owned by the Krause family for over 50 years. We happen to be on the right side of Austin, so it’s very close to our home, Roy Creek Ranch, northwest of Dripping Springs. We were there in less than an hour. It’s a beautiful park with camping, hiking trails, a butterfly garden and or course, the springs! One of the best swimmin’ holes in Texas, the springs ultimately empties into Lake Travis. With both natural and man-made pools, it’s easy to cool off on a hot summer day.

A tour of Teardrops

Marilyn had already contacted the group, and they were expecting us. They quickly found us a spot in the impressive line of teardrop trailers, and we spent the next couple of hours visiting with our new friends. Most of the trailers are custom crafted, and The Ambassador fit right in. There were a wide range of sizes an looks, and it was clear that everyone took teardrop camping very seriously. Our solar-powered beer cooler was a hit, and I was glad we had a special feature to show off.

: Rodger’s Teardrop

: Diane’s Teardrop

: Shelley’s Teardrop

Hiking the Springs

The initial flurry of introductions and tours completed, we had bite of lunch and decided to look around the park. We spent the next couple of hours exploring.

: Down to the swimmin’ hole

: A knotty problem

: Dragonflies

: House and Butterfly Garden

: Hangin’ out

: A butterfly feast

An Evening Potluck

Hikes, swims, naps and other afternoon activities completed, it was time for cocktails and a potluck. Marilyn had prepared some potato salad, and the overachievers in the group insured no-one left hungry. It was amazing to see what was produced in the tiny teardrop galleys: chips and dips, casseroles, slow-cooked pulled pork and a variety of desserts and more. An amazing day — lots of unique trailers and new friends!

Krause Springs Pool

A Solar-Powered Beer Cooler

Jim, May 31:

Tiny, Solid-state cooler

We were recently invited to the Southwest Teardrop & Vintage Trailer meet-up at Krause Springs and knowing there would be some cool trailers there, I wanted to add something unique to ours. Solar power is that not that common on teardrops yet, so it seemed a possibility. A couple of years ago, we purchased a little solid-state cooler from The Home Depot. It cost less than $30, and was shaped like an old Coca-Cola Machine. A similar product is available from Amazon, but without the Coke branding. Best of all, it could run on 120-volt or 12-volt power. Would our solar panel power it for a day?

Photo of the interior of a beer cooler with bottles and cans

Cools a 6-pack

We’ve traveled with the little cooler several times, and I routinely use it in my shop. It will hold a 6-pack in cans, or 4 short glass bottles. I’ve always got it filled with “cool ones”. I had never tried it on 12-volt power though. We also have a solid-state ice chest from Igloo, and it’s always in the car — perfect for keeping groceries cool during the hour-long trip out to the ranch. It draws about 6 amps at 13 to 14 volts (car running), so it’s not super power efficient. We once drained the car battery by forgetting to unplug it while the car sat in a parking lot for several hours. I guess that’s why I hadn’t ever tried the beer cooler on solar. Didn’t want to drain the battery.

Solar panel is removable

This was a different situation. Although the rig would be sitting idle for several hours during the meet-up, we would have sun available, and that might make it practical. I designed the solar panel to be removable, so it can be located in full sun while connected to the trailer electrical system (sitting in the shade) via a 20-foot cable. That should be sufficient to power the cooler and a a few other accessories during the day.

Well, long story short, it worked. Since we weren’t staying for the night, the Lady and the Ambassador stayed hitched and I located the solar panel on her windshield. The extension cable just made it to the normal panel connection on the trailer, and the cooler was plugged into the galley. By the afternoon, I had cold beer. The solar panel kept up just fine in spite of the partially cloudy day and occasional rain. Hmmm, now what else might we be able to power?

Current Galley

Share this:

Share this:

Share this:

Share this:

Share this:

Share this:

Share this:

Share this:

Krause Springs

A tour of Teardrops

Hiking the Springs

An Evening Potluck

Share this:

Share this: